I was looking for a nice flat bottom john boat and long story short I ended up with a 1978 Viking 190 S.I. deck boat made by Chris Craft through I knew the floor was soft but I've only ever had flat bottom aluminum very basic boats so I didn't know what I was getting into but I found Welcome to the forum.
The floor is 60” wide with two 12” wide foam/fiberglass stringers so no section of the flooring will be spanning greater than 12” side to side. Any perforations on a wet deck boat like this is the kiss of death in my mind.
I need to replace the flooring and front and rear deck. how about fiberglass/foam/fiberglass floor panels? longer then marine ply and their weight isnt that bad at all. just make sure you coat all the wood,every cut and every . forum posts represent the experience, opinion, and view of individual users.
Less expensive than "Marine deck 2000" and I think less slippery as it apparently has a higher percentage of cork. We were going to do the cockpit floor tis just a moulded non slip finish on the GRP but decided that was
What is the purpose behind canvas decking? sheathing right over the sides of the boat and care is taken with all penetrating fasteners so that water cannot leak into the ply or planked deck, this system works extremely well.
Hi, I've got a 1967 Cris Craft made mostly of mahogany plywood. The decks are covered with a white vinyl material. It has torn and needs replacement. Who has this stuff?
Welcome to the forum, Lynn. Depending on the size of boat you have, the deck is sized to meet the loads. On usual pleasure use pontoons, 3/4" plywood is what's used, but this might be a wee bit weak for your need and as
I have noticed that when I grab my pedistal or binnacle the deck floor flexes. I have good access to the underside and would like to add some
This is a discussion forum. Pontoon and deck boat forums. Welcome to the Pontoon and deck boat forums. Pontoon General. Post any question or comment you have about pontoon boats.
We are trying to choose vinyl flooring for our catamaran . We are looking at fake “teak and holly” products from PlasTEAK and Lonseal. I've searched the forums and found a few threads but no outright.
Restore Pontoon Tips & Hints. forum. How To Section (2 Viewing) Helpful Possible Solutions on Problems or Finding forum. Pontoon boat Carpet & Vinyl flooring (1 Viewing) Questions about Pontoon boat Carpet and Vinyl flooring, 10
I am new at this and have a lot of questions. I tore out the old flooring and saved it to use as a template. The inside measurement of the floor width is 50". What Lund did was rip the 4x8 pc. of plywood down to 46" and pieced in
I don't think there are too many of these around, but it is Crestliner's V-hull deck boat. IMHO, the cure can be worse than the cause and it did nothing to fix a couple of weak spots in the flooring, as most of the new floatation
Welcome to the forum. Cool deck will work, though it's heavy (not good) and requires a very stable substrate, which unencapsulated plywood isn't. On your application it'll probably crack pretty quickly. Carpet on wooden and
Join to share your project & ask us anything about your pontoon restoration. To view our older forum click here. Seats $269.99 · Flip Flop Pontoon boat Seats $269.99 · Left Pontoon boat Seat Arm $89.99 · Home → Q&A Pontoon forum
1 Mar 2016 Shipwright Robin Benjamin says modern, thin teak decks need lots of regular care, and so it's vital to follow his advice on how to keep them looking good. TAGS: boatingpractical. In the last 15 years I have worked on more
I am redoing my boat floor in a 16ft deep hull aluminum boat 75horse for motor and i have access to a bunch of left over decking and I am
thanks for letting me join this forum. I have a question re. putting a fwd. deck in a 16 ft lund aluminun boat. like a veneer) over the the existing 3" wide slats (which are screwed down to the aluminum framing under the floor.)
Hey there guys. I'm completely new to this boat wood building thing so please bear with me. The flooring will also be carpeted with marine grade carpet. Consider using some PVC decking material and no carpet. It'll look
Pontoon boat & deck boat forum • View topic - Front couches into a double bed sleeper. Carpetboating AccessoriesPontoon boat AccessoriesLake boatsBayliner boats. How to Replace boat Carpet with Woven flooring Video - Sailrite
one of the options i am considering while boat shopping is vinyl flooring instead of carpet.i think vinyl would be more durable and easy to clean but I am currently redoing my deck and giving it a lot of consideration.
The original plywood decking in the people compartment is getting soft due to a leaking water tank. As far as Express boats go, I always liked the Sea Ray 390's. Search the forums to find the information you need.
Hello, I'm finally diving in and preparing to replace the soggy floor on my 16' aluminum fishing boat & I have a few questions. Well, first of all, welcome aboard the forum! . Cheap exterior plywood and some kind of deck or porch paint for wood will hold up for several years and just use some sand as a
Hello, I own several pontoon boats. All are either fiberglass or polyethylene. When I re-deck them I use marine grade plywood and then put marine
I am trying to re-deck a pontoon boat. The owner dosen't want the 1" plywood and carpet as the deck any more. They want a fiberglass deck. They have